Description
The new Gryphon Zephyr Diamond Ring Saw offers advantages not found in other glass saws.
Please read the Special Order Products tab carefully before ordering.
- Designed for quiet operation and for low maintenance.
- The critical moving parts are shielded to minimize the abuse from the glass dust that is generated when cutting.
- The highest quality bearings and wheels are used to extend the life of these critical parts.
- The motor/blade assembly is a separate unit that can be removed from the base and used as a hand-held saw. This is useful for cutting items that cannot easily be brought to the table. A small water reservoir is built into the blade assembly housing and will hold enough water for a few minutes of hand-held cutting. When the saw is used in the normal configuration (installed in the base), the base will hold enough water for several hours of cutting.
Note:
- Always use with the face shield installed. It acts to hold the blade casing together firmly. Flip up if you prefer not to use it.
- Let the saw do the work and do not force or put pressure on the glass as you are cutting, as this exerts pressure on the blade, and you may experience more frequent blade breakages.
- The water reservoir should be emptied when not in use.
- If in a hard water area, consider using distilled water.
Please read the Special Order Products TAB
Special Order Products are not always held in stock and may have to be ordered in from our suppliers. As such your order may incur a delivery delay.
- Cannot be combined with any other product in the same order. If you require other products, please place a separate order for them.
- Not eligible for local collection.
- Extra Express Post Shipping costs will depend on your postcode. If required, please contact me and I will provide a quotation.
There are no returns for change of mind, cancellations or exchanges on Special Order Products.
I’m having trouble putting the work surface on. What’s the secret?
The work surface is designed to fit tightly so that it will not rattle. The surface is easy to install once you know the technique. To install the work surface, put it in place starting with the left rear corner. Fit the left rear corner into the slot running around the base. Next, take your right thumb and push the right side of the platform towards the centre of the saw and down. You will hear it snap into place.
What is the best way to mark the pattern before I cut?
As you undoubtedly have or will discover, the glass gets wet when you use a diamond saw. For this reason regular markers, such as Sharpies, quickly wash away. There are markers available that use paint rather than ink, and these are well suited for marking patterns on glass. The most popular of these seems to be the Pilot Extra Fine Gold and Silver Creative Marker. You can also copy your pattern onto overhead transparency material and glue or tape the pattern to the glass. In a pinch, you can use Chap Stick or Vaseline over your pattern.
Should I be taking any precautions when I don’t plan to use the saw for awhile?
We recommend that after using the saw you empty the base, add some clean water, and run it for a few seconds. This will help to rinse out the glass dust that was in the dirty water and has accumulated on the inner workings. Emptying the base of the new water is a good idea if the saw will be sitting for a while, as the lowest pulley inside the saw would otherwise be sitting in water.
How do you change the blade?
What is a Separating Blade?
A Separating Blade allows you to make inside cuts without a lead-in. Watch this video for a short demonstration of using the Separating Blade.
What sort of preventive maintenance should I be doing?
- Open the covers and inspect the working parts on a regular basis.
- Clean out any sediment that has accumulated, rinse the inside with fresh water, and inspect the rubber wheel inserts for wear.
- When you notice that the rubber has worn enough so that it doesn’t hold the blade from moving from side to side, you should replace them.
- The residue from some of the materials that you will cut is much more abrasive than others, and after a few inspections you will have a good idea of how often to inspect and clean your saw.
You can often extend the life of the blade when cutting speed diminishes by cutting a small section of a dressing stone, or alternately any hard gemstone or garden stone. This will help flush the softer material from the blade and sharpen the diamonds. Also, this is a good technique for removing burrs from the blade if you find that you are getting chipping in your glass.
How do I prevent small pieces of glass from falling through the blade hole in the work surface?
If you are trimming your piece and having trouble with the very small scrap falling through the worksurface, you can cut a small square piece of tape, such as electrical tape, to cover the hole. Cut a slit from the middle of one side to the centre of the square so that you can install the tape around the blade. If you prefer, you can buy ready cut tape.
How to install the Cutting Surface:
Free Postage (Australia only) on orders above $250 will NOT apply:
- – If more than one parcel is required. I will apply Free Shipping to the most expensive (shipping-wise) parcel. I will bill you for shipping on other parcel(s) in the order.
- – If a Seniors/Pension Discount code is used. Please consider carefully which option presents the best value to you.
Some errors may occur in shipping calculations, due to the complexities of combining products in one order. If you have overpaid shipping I will refund, or issue a credit. If you have underpaid, I will invoice for the difference.
I operate this business without assistance. Whilst I DO endeavour to ship as soon as I possibly can, I cannot guarantee to ship out the same day as the order is received. I am currently shipping orders on Tuesdays, Wednesday and Fridays.
1-10 Silverback mini glass sheets will fit into a STANDARD SMALL post box.
1-5 Hobby Squares will fit into a SMALL glass box.
Larger orders will require one or more LARGE glass boxes. Express postage on these parcels is dependant on your postcode. Please email me for a quote if required.
I package carefully. However, damage may occur during transit. Product is shipped entirely at your own risk.
International Shipping:
My website does not allow international customers to check out. Please e-mail me a list of the products you want (you can create a wishlist and email it to me), your shipping address and the preferred method of payment. I will prepare a quote and email it to you. If acceptable, I will send a payment request/invoice. Items will be shipped once payment has cleared.
Apologies – I do NOT ship glass internationally. Grouts ship to Australia and New Zealand only.
Your understanding is appreciated.
